Firmware Updates

TX-RZ920

Notice of Firmware Update for TX-RZ920

A firmware update for the TX-RZ920 network A/V receiver is available through the unit's USB input. The latest update includes the following content:

Latest Firmware Number (16 digits):1060-8010-3050-0010

As of 11 October 2018

  • Adds support for Amazon Music.
    *Amazon Music service requires that you have Amazon Prime account or Amazon Music Unlimited account
    *Onkyo Controller App is required for initial set-up of Amazon Music.
    For detail about updated function, please refer to the link below.
    http://www.onkyo.com/manual/sup/upd/amazon_onk.pdf
  • Adds support for eARC.
    HDMI cable needs to be Ethernet-enabled HDMI cable.
    For detail about updated function, please refer to the link below.
    http://www.onkyo.com/manual/sup/upd/earc_onk.pdf
  • Adds setting of Preset Volume for Sonos Connect.
    For detail about updated function, please refer to the link below.
    http://www.onkyo.com/manual/sup/upd/sonosconnect_onk.pdf
  • Enhanced security.
    Depending on the Firmware version, update will be needed 2 times.
  • Minor bug fixes and improvements stability.

As of 21 August 2018

  • Enhanced security.
  • Adds support for Deezer HiFi.
  • Depending on the Firmware version, update will be needed 2 times.

As of 5 June 2018

As of 4 April 2018

  • Improve the noise during playback via USB/Network

As of 31 January 2018

  • Adds support of external audio inputs* for "FlareConnect".
    *For detail about external audio inputs, please refer to the link below.
    http://www.onkyo.com/flareconnect/
  • Minor bug fixes and improvements stability.

As of 30 October 2017

  • Adds support for new multi-room audio playback function "FlareConnect".
    *All audio devices in group and "Onkyo Controller" App is required to update to the latest version.
    Setup Guide: www.intl.onkyo.com/next_generation/setup.html
    Introduction of multi-room audio functions: www.intl.onkyo.com/next_generation
  • Improvement for pass-through function of Dolby Vision signal.
  • Minor bug fixes and improvements stability.

Precautions for TX-RZ920 Firmware Update

  • Please read the update instructions carefully before beginning.
  • The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the power supply to the A/V receiver until it is time to restart it.
  • Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing the ON/STANDBY button and then try updating again from the beginning.
  • Updating the firmware and adjusting the settings will be done automatically, but may take some time to complete. Please follow the procedures as instructed when you update. Note that the update may fail, or cause problems for your A/V receiver, if you do any of the following:
  • Pull out the A/V receiver's power cord;
  • Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical outage);
  • Insert or remove the LAN cable from a device in your network when updating over a network;
  • Insert or remove a USB memory device from the A/V receiver when updating via USB;
  • Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.

If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will repair the unit for a fee.

How to Install Firmware Update for TX-RZ920

Click below for instructions on how to install the update.

Click below to download the firmware update to your PC, for subsequent installation on your receiver via its USB port.