Firmware Updates

TX-NR717

Notice of Firmware Update for TX-NR717

A firmware update for the TX-NR717 network A/V receiver is available through the unit’s network connection or USB input. The latest update includes the following content:

Latest Firmware Number (12 digits):1120-8103-0100-0000

As of 28 Feb 2013

Information Concerning Firmware Update for Onkyo Network Receivers

Onkyo has discovered there is a possibility of failure when updating receivers to this new firmware package via ethernet in certain network environments.

For this reason, we are now only releasing a firmware file for installation via USB port / flash memory device.

Users should first check to see if their network receiver is running the latest firmware (1100-7101-0100-0000 released July 24, 2012) before installing this update via USB.If your network receiver is not running firmware version 1100-7101-0100-0000, please update your receiver to this version via the network facility before proceeding further.

To check your firmware version, press the “Home” button on your remote control. Highlight “F/W Update” or select the “Firmware Update” icon and press enter.

Your current firmware version will be displayed on the front panel of your A/V receiver as well as your TV screen.

Should you encounter any difficulties when performing this update, please contact us.

We appreciate your understanding and apologize for any inconvenience this issue may cause.

  • Improves picture output of 1080p/24 sources;
  • Improves the playback stability of FLAC files via Network/USB;
  • Corrects the sound leak issue between Main and powered Zone2/3 when activating Powered Zones;

As of 24 July 2012

  • Supports Onkyo Remote2 for iOS version: 1.30 or later -Adds support for high end models & audio streaming from iOS device;
  • Supports Onkyo Remote for Android version: 1.30 or later-Adds support for high end models;

    • *it is also necessary to update the App;

  • Improves operation of "Power on" of remote control;
  • Adds support of playback of Dolby True HD 192kHz file format by using Home Media Function;

    • *Notice;

    Limitation of when using UWF-1

    1. Only 64 kHz and less sampling rate is supported;

    2. Dolby TrueHD and DSD is not supported when using Home Media Function;

    3. Using at rear USB port is not supported when using Home Media Function;

As of 15 June 2012

  • Corrects unexpected instance where a portion of the internal memory may stop working during operation*;

    • *see below for further details;

  • Adds UBT-1 Support ;

As of 8 June 2012

  • Corrects unexpected instance where a portion of the internal memory may stop working during operation*;

    • *All Setting will be cleared after this update. Initial set-up must be performed again including Audyssey calibration.

  • Improves update functionality;

How to Check if Your Firmware Version is Up To Date

To Check if your firmware is up to date, go into Setup -> Hardware Setup -> Firmware Update and check the 12-digit number (xxxx-xxxx-xxxx). If any numbers differ from the latest version available, please update your unit.

Precautions for TX-NR717 Firmware Update

  • Please read the update instructions carefully before beginning.
  • The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the power supply to the A/V receiver until it is time to restart it.
  • Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing the ON/STANDBY button and then try updating again from the beginning.
  • Updating the firmware and adjusting the settings will be done automatically, but may take some time to complete. Please follow the procedures as instructed when you update. Note that the update may fail, or cause problems for your A/V receiver, if you do any of the following:
  • Pull out the A/V receiver’s power cord;
  • Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical outage);
  • Insert or remove the LAN cable from a device in your network when updating over a network;
  • Insert or remove a USB memory device from the A/V receiver when updating via USB;
  • Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.

If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will repair the unit for a fee.

How to Install Firmware Update for TX-NR717

Click below for instructions on how to install the update.

Click below to download the firmware update to your PC, for subsequent installation on your receiver via its USB port.